Please wait a minute...
Chinese Journal of Engineering Design  2015, Vol. 22 Issue (3): 278-283    DOI: 10.3785/j.issn. 1006-754X.2015.03.012
    
Research on the characteristics of the TBM thrust hydraulic system under fundamental vibration
YANG Zhong-jiong1,2,LU Yao-zhong2,ZHOU Li-qiang1,2,LI Hong-bing2
1.State Key Laboratory of High Performance and Complex Manufacturing, Central South University, Changsha 410083, China;2. College of Mechanical and Electrical Engineering, Central South University, Changsha 410083, China
Download: HTML     PDF(2376KB)
Export: BibTeX | EndNote (RIS)      

Abstract  TBM (tunnel boring machine) will be affected by strong external vibrations when it is working. In order to study the influence characteristic of the strong vibrations to the thrust hydraulic system, firstly the principle of the TBM thrust hydraulic system was summarized, then the AMESim model for the thrust hydraulic system under fundamental vibration was established, the correctness of the simulation model was experimentally verified, and finally the speed fluctuations and frequency domain influenced by external vibration frequency and the vibration amplitude were studied. Results showed that, hydraulic cylinder pushing speed was influenced by external vibration, the impact became the biggest when the external vibration frequency was 40-60 Hz; the influence of the change of the vibration amplitude was lower than the change of the vibration frequency; the cutoff frequency of the thrust hydraulic system was about 13 Hz. When the outside vibration frequency was higher than it, the frequency characteristic of hydraulic system would become worse, and the hydraulic cylinder was difficult to make the appropriate response to the input signals.

Key wordsTBM      thrust hydraulic system      fundamental vibration      simulation     
Received: 04 December 2014      Published: 28 June 2015
Cite this article:

YANG Zhong-jiong,LU Yao-zhong,ZHOU Li-qiang,LI Hong-bing. Research on the characteristics of the TBM thrust hydraulic system under fundamental vibration. Chinese Journal of Engineering Design, 2015, 22(3): 278-283.

URL:

https://www.zjujournals.com/gcsjxb/10.3785/j.issn. 1006-754X.2015.03.012     OR     https://www.zjujournals.com/gcsjxb/Y2015/V22/I3/278


基础振动下TBM推进液压系统工作特性研究

硬岩掘进机(tunnel boring machine,TBM)在工作过程中会受到外界强振动的影响.为了研究强振动对其推进液压系统的影响规律,首先总结了TBM推进液压系统的工作原理,然后建立了推进液压系统在振动环境下的AMESim仿真模型,并用实验验证了仿真模型的正确性,最后分析了外界振动频率、振动幅值对推进液压系统推进速度波动的影响规律以及振动幅值、振动频率对液压系统频响特性影响规律.仿真结果表明:液压缸推进速度受外界振动影响较大,当外界振动频率为40~60 Hz时影响最为剧烈;外界振动幅值的改变对液压系统的影响比振动频率产生的影响小;推进液压系统的截止响应频率约为13 Hz,当外部振动频率大于系统截止频率时,系统的频响特性会迅速变差,液压缸难以对输入电信号作出相应的响应.

关键词: TBM,  推进液压系统,  基础振动,  仿真 
[1] Shao-yu TANG,Jie WU,Hui ZHANG,Bing-bing DENG,Yu-ming HUANG,Hao HUANG. Simulation and experimental research on temperature field of multipole magnetorheological clutch[J]. Chinese Journal of Engineering Design, 2022, 29(4): 484-492.
[2] Ke-jun LI,Min-ya DENG,Wen-jing HUANG,Yu ZHANG,Jia-wang ZENG,Miao-lin CHEN. Study on working characteristics of swing system of concrete wet spraying machine[J]. Chinese Journal of Engineering Design, 2022, 29(4): 519-526.
[3] Chen WANG,Bo GAO,Xu YANG. Lightweight design of Stewart type six-axis force sensor[J]. Chinese Journal of Engineering Design, 2022, 29(4): 419-429.
[4] Wei GAO,Wei ZHANG,Hai-tao GU,Ling-shuai MENG,Hao GAO,Zhi-chao ZHAO. Analysis of motion characteristics of large deep-sea AUV unpowered spiral diving[J]. Chinese Journal of Engineering Design, 2022, 29(3): 370-383.
[5] FAN Xiao-yue, LIU Qi, GUAN Wei, ZHU Yun, CHEN Su-lin, SHEN Bin. Simulation and experimental research on thermal effect of electromagnetic micro hammer peening mechanism[J]. Chinese Journal of Engineering Design, 2022, 29(1): 66-73.
[6] LI Yang, NIE Yu-fei. Design and analysis of heat insulation sealing door of sodium combustion test plant[J]. Chinese Journal of Engineering Design, 2022, 29(1): 115-122.
[7] ZHANG Qin, PANG Ye-zhong, WANG Kai. Simulation analysis and experimental research on robot pedaling weeding process[J]. Chinese Journal of Engineering Design, 2021, 28(6): 709-719.
[8] ZHANG Shen-tong. Analysis of landing load of aircraft landing gear based on virtual prototype technology[J]. Chinese Journal of Engineering Design, 2021, 28(6): 758-763.
[9] CHEN Zhen, XIONG Tao, YANG Yan-qing, XUE Xiao-wei. Sealing performance analysis and structure optimization of sealing ring of soluble ball seat[J]. Chinese Journal of Engineering Design, 2021, 28(6): 720-728.
[10] XIN Chuan-long, ZHENG Rong, YANG Bo. Research on the design and connection control scheme of AUV underwater docking system[J]. Chinese Journal of Engineering Design, 2021, 28(5): 633-645.
[11] FU Gui-wu, WANG Xing-bo, TIAN Ying. Research on application of digital twin based on intelligent production line of five-axis machining center[J]. Chinese Journal of Engineering Design, 2021, 28(4): 426-432.
[12] YU Ru-fei, KOU Xin, CHEN Wei. Simulation analysis of novel surface texture based on CFD[J]. Chinese Journal of Engineering Design, 2021, 28(4): 466-472.
[13] XU Yong-ming, TANG Yi-fan, ZHANG Sheng, SHI Jian-xun, YU Yun-zhong, ZHANG Zheng. Simulation and experimental research on automatic straightening of power cable[J]. Chinese Journal of Engineering Design, 2021, 28(3): 329-334.
[14] YAN Guo-ping, ZHOU Jun-hong, ZHONG Fei, LI Zhe, ZHOU Hong-di, PENG Zhen-ao. Design and optimization of magnetic compression correction device for paper-plastic composite bag[J]. Chinese Journal of Engineering Design, 2021, 28(3): 367-373.
[15] LIU Yong-jiang, PENG Xuan-lin, TANG Xiong-hui, LI Hua, QI Zi-mei. Resonance failure analysis and optimal design of axial cooling fan[J]. Chinese Journal of Engineering Design, 2021, 28(2): 203-209.